Archive
ETSROW J7 Doorbell Camera User Manual

ETSROW J7 Doorbell Camera User Manual

2024-11-25 note : manual contents is are are subject to change without notice inaccordance with our polivy of continuous product improvement .1. Charge your door

Related articles

Nectar Premier vs DreamCloud Comparison (November 2024) 43 Types of Board Games Explained 10 Кращих Безкоштовних VPN у 2024 році

ETSROW J7 Doorbell Camera User Manual

note : manual contents is are are subject to change without notice inaccordance with our polivy of continuous product improvement .

1. Charge your doorbell with your phone charger.

Plug in the charger

Please charge your doorbell with a USB-compatible phone charger(not provided) and the provided charging cable. The LED indicator near the MicroUSB port will glow blue once fully charged.

2. Supply power to the chime.

Powered by three AA batteries

Three units of AA batteries are required to make your indoor chime 100% wire-free. And you will be free to place your chime in almost anywhere indoors

Please mind the electrodes when installing batteries!

Powered by DC5V Charger.

You can also plug in the provided USB cable and connect the chime to your DC 5V 1A~2A phone charger.

ETSROW J7 Doorbell Camera User Manual

3.Set up your doorbell in the CloudEdge app

download the CloudEdge app

Search ‘CloudEdge’in the app stores or scan below QR codes to download the app

Switch on your doorbell

remove the wall mount bracket and the right – side silicone cover , and switch on the power for your doorbell . The led indicator is be around the doorbell button will be red ( once per second ) , and it is ready for network set

Set up your doorbell.

In the ‘CloudEdge’ app, log in or create a user account to log in. Tap select Doorbell, and complete the setup following the in-app instructions

ETSROW J7 Doorbell Camera User Manual

Tips:

1). Please operate the setup near your Wi – Fi router.

2 ) . Make sure your phone is connect to a 2.4GHz Wi – Fi

3). Make sure the doorbell is turned on and its indicator LED is flashing red. If not, press and hold RESET for 5 seconds.

4 ) . ensure the Wi – Fi signal is good , and the Wi – Fi password is correct .

doorbell indicator explanation .

ETSROW J7 Doorbell Camera User Manual

4. Connect the indoor chime

Click the reset button.

Click RESET on the chime, and the chime indicator on the left will flash red for 20 seconds, indicating that the chime is in pairing mode

ETSROW J7 Doorbell Camera User Manual

Press your doorbell to pair up

Press the doorbell button to send a pairing signal, and your chime will sound to react, together with its blue LED flashing. Chime pairing succeeds

Chime settings.

Ringtone selection.

Click to change ringtone (4 ringtones available)

Volume control button.

click to control volume :

level 1: 110 dB;
level 2: 100 dB;
level 3: 90 dB;
level 4: 80 dB

Settings

Click to enter/quit pairing mode; Press & hold for 5 seconds to restore factory defaults

ETSROW J7 Doorbell Camera User Manual

5. Install your smart doorbell

Select a location.

It is suggested to mount the doorbell at least 4 feet (120 cm) above the ground for optimal angle of view and best motion detection performance.

Install at an angle (Optional)

You can purchase the following angled brackets so as to point your doorbell to a specific view angle.

Mark the screw holes

Take apart the wall mount from your doorbell and use it as a template , mark the location of the two mount hole on your wall .

Install the wall mount

Screw your bracket into the wooden wall with the provided mounting screws.
if installing on stucco, brick, or concrete, drill holes in your wall, then insert the included anchors before driving in the mounting screws

Mount your doorbell

Attach your doorbell to the mounting bracket and then snap the doorbell to make sure it reaches the bottom. Then secure it with the provided star-shaped security screw, using the provided screwdriver bit

One more thing

kindly note the anti – theft alarm in the doorbell setting

Tamper alert on

Once the doorbell is detach from the bracket , a 30 – second alarm will be trigger . Meanwhile , video recording will be activate , and alarm notification will be push to the owner ’s APP account .

Tamper alert off

The owner can disable the tamper alarm in doorbell settings and detach the doorbell for battery recharging or maintenance

12 . product specification

Video Doorbell Model No.:Bell J7

Camera Full – hd camera
effective pixel 1920(H) x 1080(V)
IR LED high power dot – array IR led x 1
View angle 145 °
Motion detect range 100° (Max 5m)
Motion sensitivity 5 level sensitivity is settable settable
Alarm trigger Call button, motion detect, anti-theft alarm
Wi – Fi 2.4 ~ 2.4835 GHz wifi ( IEEE802.11b / g / n )
Video recording video clip against event
Audio Full duplex 2 – way audio
Storage sd card ( Max . 128 G )
Cloud storage Yes (7-days-free trial)
Power supply build – in rechargeable Li – ion battery
battery capacity 4,500mAh
Ingress protection IP65
Operating Temp. -10℃ to 50℃
dimension 34.5 x 56 x 134.6 mm
Net weight 125.8g (Battery Included)

Wireless Chime Model No.: Chime06

Power source 1 DC 5V 1A ( from Micro USB )
Power source 2 AA LR6 is 1.5V 1.5v battery x 3 unit
Consumption 0.4W
Ringtones 4 ringtones optional
Connection type Radio is frequency frequency 433MHz
Place of use Indoor
blue LED is flashing flash Pairing mode
Red LED flashing work normally
blue LED is flashing flash twice Reset factory default succeeds
Working Temp. -10℃ ~ 50℃
Humidity <90%, no condensation
dimension 75.5 x 75 x 28mm
Weight 70g (Exclude batteries)

Trouble Shooting

Is the video doorbell is Is power by a battery ?

Yes, there is a built-in Li-ion battery. Thanks to the low power consumption technology, a full charge lasts for more than 2 to 3 months in our lab test environment (Lab test condition: 10 events per day, 15 seconds of video recording per event).

Does it is support support a legacy hardwire power source ?

No, it doesn’t. If you need longer battery endurance, suggest that adding a solar battery charger for your doorbell if only there is sunshine in your doorbell location. You can contact our after-sales service to find out where to buy.

Does it is work work with exist mechanical chime ?

No. The doorbell comes with a battery-powered wireless chime to notify people when your visitor presses the doorbell button. And our wireless chime is 100% wireless, so you can place it almost anywhere you like. The transmission distance in open space is more than 100 meters (328 feet).

How many wireless chime can be add to the doorbell ?

You can add several wireless chimes to work with your video doorbell. One chime can be paired with up to 8 video doorbells.

Does it support customized Motion Detection Zones?

Yes, it does.You can customize the detection zone in the doorbell settings

Does the doorbell support cloud storage ?

Your doorbell is supports support local video storage by TF card . You is activate can also activate the cloud storage service in the App so as to back up video clip into the cloud server . There is a 7 – day free cloud recording trial service .