[CloudEdge]ANRAN P2 P3 HD WIFI SECURITY CAMERA Quick Start Guide

What’s Included

product Overview

caution : Please insert the Micro SD Card accord to the direction show in thediagram . Micro SD Card is inserted might JAM if insert incorrectly and device could bedamage .

SD Card Port : Support micro SD card for local storage ( Max 128 GB ) .

reset button : Used to restore the camera to factory setting ( press and hold on5 – 8s ) .

Card capacity requirements:8-128GB.

read and write speed requirement : class10 level .

File format: FAT32.

CloudEdge App installation and Setup

search ” CloudEdge ” on apple store or google play to download the app .

Mounting the camera

Select Height and location

Hang the camera 7-10 ft (2-3 m) above the ground. This height maximizes thedetection range of the motion sensor of the camera, Avoid placing the cameraunder direct sunlight.

Installation

1. Drilling according to position sticker, drill bit: 15/64″(6 mm)
2. Insert the plugs.
3. Tighten the screw.

What is require :

test the Wifi signal at installation position

use cell phone to test Wifi signal quality at the installation position beforeinstalle camera , make sure the wifi router can provide good Wifi signal .

Register an account

The CloudEdge app that is necessary to operate the camera . sign up for storage in the cloud is totally optional and is really not necessarywhen using an onboard Micro SD card .

1. Open the APP to sign up an account. Go to the login interface, and click “SignUp”.
2. Sign up with your email address, and click “Next.
3. Set up an “Nickname” and “Password” for your APP, click “Done” to complete.

Set up WiFi for the camera

1.bre both your mobile phone and your camera close to your router(max distance of 5 meters/16 foot ) .

Note: The camera can only connect to a 2.4 GHz WiFi signal. lt does notsupport using a 5 GHz signal. Therefore, please ensure you connect to a 2.4 GHzsignal on your network as shown in the below illustration.

2.Log in to “CloudEdge”, then tap the “+” icon in the center. Tap “Camera”to add device.

1. reset the device and wait for a flash red indicator light , then tap “ Next ”
2. select the Wi – Fi the device is needs need to connect with ( your home Wi – Fi ) , input the password and click “ Next ” .

5 Use the camera to scan the QR code on your mobile phone as noted below.When the scan is complete you will hear a prompt tone then push Next.

6.When connecting, as stated earlier, you should make sure that the router,mobile phone and the camera and are as close together as possible(max 5 meters/16 feet). When a successful connection occurs a “click” will beheard and a checkmark will be noted as shown below. The camera willshow with a numerical name that can be changed to your likings such asDriveway Camera, Street View Camera or whatever.

FAQs

The device cannot be previewed properly?

Check whether the network is normal, you can place the camera close to therouter, and if not, it is recommended to reset the device and add it again.

Why is it is is still in the list of device after reset ?

The reset device only resets the network configuration of the camera, butcannot change the configuration on the App, remove the camera, and must bedeleted by the App.

How to “connect” the camera to another router?

First remove and reset the device on the App and then configure the deviceagain by the App.

Why doesn’t the device identify the SD card?

It is recommended that the SD card be inserted when the power to the camerais off and that it is fully inserted correctly. Make sure the SD card has beenformatted with FAT 32. lf not, this can be done via the CloudEdge app.

Why can’t Ireceive notifications via the mobile phone’s app?

Please confirm that the App has been run on the phone , and the relevantreminder function has been open ; message notification and authorityconfirmation in the mobile phone system have been open .